Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
They are making several good pointers regarding How to Install a Bathtub overall in the content underneath.
Mounting a tub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, and often, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately hard task. If the old bathtub is conveniently obtainable, the job can move speedily; if you need to open a wall to get rid of the old tub as well as position the brand-new bath tub, the job is a lot harder. In either case, the job is within a house handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. See to it you have actually qualified on your own for the work and also are comfortable trying it. Instead of working with a professional to take over a halfway-completed job, it is better to think about using one prior to you start. Possibilities are you may require a professional plumber to make tube connections.
This post will help you install a brand-new bathtub in your bathroom if you have actually already purchased a brand-new tub and also don't require to transform the arrangement of your previous water system pipes.
Your devices and product checklist should make up the following:
Preparing for the Installment
Firstly, the supporting framework supplied with the bath needs to be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps unit to stop stress on the tub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its last setting.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of removing the existing faucets can be quite bothersome as a result of the limited gain access to that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a towel all set for the continuing to be water that will come from the pipelines. When the supply pipelines have actually been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
Before carrying on to fit the new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, place the bathtub in the called for position. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make certain that the tub is leveled all round. This can be attained by inspecting the spirit level as well as readjusting the feet on the tub until the level checks out level.
To install faucets, fit the bottom of the outermost flexible tap adapter to the ideal supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the water supply and examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill the bathtub as well as also check the overflow outlet and the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the bathtub ought to wait till the tub has been utilized at least once as this will certainly resolve it into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin ensuring that the washers are in location between the faucet and also the sink. Protect the faucet in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical faucet adapters. The former type ought to be connected to the tap finishes first, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to fracture an inflexible seal, triggering the water to permeate the wall surface between the bathroom and also the tiling, bring about issues with wetness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your components as well as installations. They are marketed in tubes as well as cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly fill the tub with water before sealing, to allow for the motion experienced when the bathtub is in use. The sealer can break relatively very early if you do not consider this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you liked our article on How to Install a Bathtub Yourself. Thank you so much for spending some time to read our piece of content. Sharing is caring. One never knows, you will be helping someone out. I am grateful for your time. Please pay a visit to our site back soon.
Go Company Report this page